2024 Jagdpanther No43 build log.

[chris fry]

Time for some paint, Temperature has warmed up a little so can start applying,
Will try and put in the pictures what paints and materials we use,

underside first, keyed the surface using scotch brite, not necessary as the upol etch primmer will bond itself to the metal but it will help, then wipe clean with thinners or panel wipes, masked up all the axles/bearings etc.

upol etch primmer on, this primmer works out around £5/6 pound a can, will expect to use 4 to 6 cans on this model.

for a base color on the underside, used a light green, as this color wont been seen and not much weathering color not critical, used half of this can,

Once the underside has dried will turn over and start primming the top side and color the inside,
Regards, Chris.

[chris fry]

More hull painting,

Hull now in etch primer,

Inside as well. with all the other panels/gun mount and wheels primed now, total used 6 500ml cans.

Inside sprayed gloss white.

Again used upol spray paint, Used 2 500ml cans, inside hull/underneath of roof and inside rear segment, also battery tray, around £6/7 pounds a can.

Once all dry will start on filling over fasteners not to be seen, Dummy welds added and texture surface applied, Again will show pictures as we go along on method and products used, Also can now start adding the motion pack,
Thanks chris.

[chris fry]

As the cold spell continues and not ideal for painting etc carried on with installing the motion pack,

Motors assembly fitted,

R/H assembly fitted, Follow instructions with belt tension, They dont need to run very tight.

Smoker all piped up, Some non kit parts used here, Used heat shrink on the joints to aid sealing but it still allows joints to twist if you need to disassemble at a later date.

General layout of electronics, None of the modules are fixed down yet, I use dual-lock to do this, this makes attaching/removal easy and acts as a cushion for the modules, A lot of tidying up once testing is finished, Just need to add receiver, Audio unit, Recoil and gun actuators etc/etc.

Hopefully warming up next week so we can continue with painting etc,

[Derek Attree]

Hi Chris
Nice neat layout and good to see the new motor set up.

Regards Derek

[chris fry]

Some more progress, Again anything you want to know or advice please feel free to ask,

Filling over the fasteners not to be shown, Using p38 body filler, Price is on the tin, Once it has set use emery paper to smooth down,

Replicating the texture look, Use a high build filler, Apply with a brush by stipulating (dabbing), This filler is like a very thick paint, Use straight from can, Use in a ventilated area as it does stink, Cost around £20 a tin but this will do a dozen++ tanks.

Close up of texture result, The more you work the filler when applying will give a more texture look, Which will really show once the main color scheme is applied. Just trying to give a depth look to the paint rather than the flat new look metal finish.

Dummy welds, Used milliput putty, Around £5 a pack, It comes in a 2 part application, Roll the 2 parts together, Keep it moist as this helps it not sticking to your fingers, Then once mixed roll in to a thin bead then apply where you want the weld, Then with a small flat edge impress the weld lines,

Tool used for squeezing out a perfect bead of milliput, Saves rolling it by hand, Just fill the tube up with the mixed putty and wind the handle, Best £8 spent. Just make sure you clean well after use as milliput sets like concrete,

Next stage will be applying the base colors.

[Steve Stuart]

A useful device, who is the supplier and what is it's name so I search for it?
Thanks Steve

[chris fry]

Evening Steve,
Try searching for DIY craft extruder, eBay is your best bet,
Regards, Chris.

[Dan Fuhrman]

Chris,

Thank you for posting! Best new modeling tool for 2025.

Dan