2025 ARMORTEK KIT SURVEY

Over the last few years we have brought out a whole series of kits as a direct result of your feedback - kits like the Pershing, JagdPanther, Hetzer, Leopard 2A4, and more recently the Sd Kfz 7, 88mm Flak 36 and the upcoming Challenger 2.

So, in keeping with what has become and annual tradition, here is your opportunity to once again influence our future production plans.

We have added in some "guide pricing" next to the names of the models. This is a rough estimate of the price at the current rates.

Thanks in advance for your input and we look forward to the results.

Help Needed: 222 Small Parts

Forum for discussion relating to the Sdkfz 222
Post Reply
Jan_Donadoni
Posts: 151
Joined: Fri May 21, 2010 8:20 am
Location: Italy
Has liked: 2 times
Been liked: 6 times

Help Needed: 222 Small Parts

Post by Jan_Donadoni »

Hello,
I've two little problems with my 222 build.The model (and I) had to change house a few times in the last few years. No pieces went missing, but two of them left their identification bag and no I cannot find out where they should go. Was even unable to find their picture in the building instructions.
Can anyone help me?
20971A08-B324-424D-9F00-4618159A5373.JPG
My men can eat their belts, but my tanks have gotta have gas.
(George S. Patton)
Top
mark lawson
Posts: 720
Joined: Tue May 14, 2013 9:14 pm
Location: Solihull
Has liked: 2519 times
Been liked: 444 times
Contact:
Contact mark lawson

Re: Help Needed: 222 Small Parts

Post by mark lawson »

If memory serves me well, these are the exhaust brackets
Werkstatt - 5, 1/6 Panzer parts. werkstatt.five@gmail.com
RAG Militärmodellbau
IG Militärmodellbau
Top
User avatar
Adrian Harris
Posts: 5119
Joined: Thu Jul 12, 2007 10:46 pm
Location: Berkshire (UK)
Has liked: 1475 times
Been liked: 1674 times

Re: Help Needed: 222 Small Parts

Post by Adrian Harris »

Mark is correct, though very few completed models on the forum seem to have them fitted.

Part number is CJ0339 - Exhaust Stay.

2009-01-17_14-15-50.jpg

Fitting is described on page 17 in Release 1 of the instructions:

"Dry fitting of the exhaust system is recommended before using adhesive in the final assembly. Slide the exhaust box onto the pipe and rotate into place. Fit the cowls to the hull side. Push the pipe into the cowl and rotate into position. Slide the stay over the outlet end of the pipe and twist along it’s length until the top end lines up with the rear mudguard, rear fixing holes. Retain using the existing bolt. Once all parts are lined up, clean and fit using Loctite."

Adrian.
Contact me at sales@armortekaddict.uk for details of my smoker fan control module
Top
Jan_Donadoni
Posts: 151
Joined: Fri May 21, 2010 8:20 am
Location: Italy
Has liked: 2 times
Been liked: 6 times

Re: Help Needed: 222 Small Parts

Post by Jan_Donadoni »

Thank you very much.
Indeed I had some memory it went to the exhaust system, but was totally unable su figure out this solution. Without your info I'd probably dropped the pieces.
My men can eat their belts, but my tanks have gotta have gas.
(George S. Patton)
Top
User avatar
Alvin McCall
Posts: 16
Joined: Sat Jul 14, 2007 1:35 pm
Location: katy Texas
Been liked: 1 time

Re: Help Needed: 222 Small Parts

Post by Alvin McCall »

same here I have them but never knew where they went ,
Top
Post Reply

Return to “Sdkfz 222”