Another Tiger
-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
-
Chang
- Posts: 1115
- Joined: Mon Jul 21, 2008 1:45 am
- Has liked: 16559 times
- Been liked: 487 times
Re: Another Tiger
------------------------------------------------------------------
Es braust unser Panzer im Sturmwind dahin.....
Es braust unser Panzer im Sturmwind dahin.....
-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
Re: Another Tiger
my whole family and I have covid right now, but I am still turning screws in here! mostly just feels like I have a severe cold.
-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
Re: Another Tiger
covid is miserable. still found the strength to work on my tank though. hull sides loosely assembled.
-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
-
Robert E Morey
- Posts: 2349
- Joined: Wed Jul 18, 2007 12:59 am
- Location: Seattle, WA USA
- Has liked: 161 times
- Been liked: 830 times
Re: Another Tiger
Brian
Sorry to hear everyone has the crud. Hang in there. I'm doing everything I can to not get it. Keep tinkering! Good progress.
Best regards,
Bob
Sorry to hear everyone has the crud. Hang in there. I'm doing everything I can to not get it. Keep tinkering! Good progress.
Best regards,
Bob
-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
-
Chang
- Posts: 1115
- Joined: Mon Jul 21, 2008 1:45 am
- Has liked: 16559 times
- Been liked: 487 times
Re: Another Tiger
To lock M3 screw and nut on these positions is a headache to me (Sorry borrow your photo again, Brian) :
If lock them before installing of two driving motors, it'll be quite difficult to install the driving motors later on.
Yet vice versa, if install two driving motors before locking them, it'll be extremely difficult to do so as well.
Any better ideas from all of your skilful builders?
Lerh Chang
If lock them before installing of two driving motors, it'll be quite difficult to install the driving motors later on.
Yet vice versa, if install two driving motors before locking them, it'll be extremely difficult to do so as well.
Any better ideas from all of your skilful builders?
Lerh Chang
------------------------------------------------------------------
Es braust unser Panzer im Sturmwind dahin.....
Es braust unser Panzer im Sturmwind dahin.....
-
Søren Sandvold
- Posts: 106
- Joined: Wed Mar 24, 2021 5:41 pm
- Has liked: 380 times
- Been liked: 261 times
Re: Another Tiger
Lerh Chang
I've had my motors and motorspacers in/out a couple of times with all of the panels locked/screwed down. Cant say I encountered any problems doing so
A bit fiddly yes, but not particular difficult.
I've had my motors and motorspacers in/out a couple of times with all of the panels locked/screwed down. Cant say I encountered any problems doing so
A bit fiddly yes, but not particular difficult.-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
Re: Another Tiger
It’s been a while but I definitely have installed/removed motors in a completely build hull. That reminds me that I’ll have to order motion soon.
Like mentioned before it’s not terribly difficult. Having a variety of wrenches helps! Sometimes I use a multi tool for bicycles or even a disposable key that may be modified or cut to a certain length so I can get it into a tight spot.
Like mentioned before it’s not terribly difficult. Having a variety of wrenches helps! Sometimes I use a multi tool for bicycles or even a disposable key that may be modified or cut to a certain length so I can get it into a tight spot.