Phils Famo build

florian rudolf · Post by **florian rudolf** » Thu Dec 20, 2018 9:44 am

Yes that's true Phil, but at the corners it will not be enough to get the rounding suitable. Made of sheet metal fenders can be provided with smashes to create a used look...
Today is my last working day. than hollyday till 07.01.19 so much time to build and creat some nice things

Florian

Phil Woollard · Post by **Phil Woollard** » Thu Dec 20, 2018 12:22 pm

I,ve profiled one side of the fenders and I think it looks ok?

florian rudolf · Post by **florian rudolf** » Thu Dec 20, 2018 12:29 pm

Hi Pfil,
that looks good on this side. How is the other side? - The inner side is verry round.

Phil Woollard · Post by **Phil Woollard** » Thu Dec 20, 2018 12:58 pm

I have done both sides of this side, that's as much as I want to remove, it should look better when it's all the same colour!

Chang · Post by **Chang** » Thu Dec 20, 2018 1:27 pm

Great looking on rounded fenders Phil.

Ever thinking of adding two short ribs and deepen the footstep on this area?

: On historical photos the footstep is always deeper and dark....; DSC_1783-2.jpg (96.9 KiB) Viewed 1792 times

Cheers,
Lerh Chang

florian rudolf · Post by **florian rudolf** » Thu Dec 20, 2018 2:00 pm

Hi Chang,
that part you mean, is verry massiv, so I'm going to mill off all the stuff inside this part. The stepp is than a hole. Later I mill the smal stripes...
Much work to do..

Phil Woollard · Post by **Phil Woollard** » Thu Dec 20, 2018 3:12 pm

Hi Chang, that step hole will need milling, I may deepen it and and paint the hole very dark inside, are you going to round off your fenders? There are lots of rivet details on the fender which also need adding, I will add the two ribs.

Brian Ostlind · Post by **Brian Ostlind** » Thu Dec 20, 2018 3:57 pm

I love the fenders!

Phil Woollard · Post by **Phil Woollard** » Thu Dec 20, 2018 4:38 pm

Cheers mate, heres some more.

florian rudolf · Post by **florian rudolf** » Fri Dec 21, 2018 4:44 pm

Hi Phil,
You have seen the problem with the m4.... you took put the braket? Is there not too less drill in the metall to tighten the mudgaerd enough?
Florian

Phil Woollard · Post by **Phil Woollard** » Fri Dec 21, 2018 5:03 pm

Hi Florian, there's enough metal in the m3 clearance hole to tap an m4, so I will drill an m4 clearance from below in the fender and fit an m4 button head that way.

Phil Woollard · Post by **Phil Woollard** » Fri Dec 21, 2018 6:31 pm

More detail for the fenders.

Steve Lewington · Post by **Steve Lewington** » Fri Dec 21, 2018 9:17 pm

Hi phil
love the use of plasie card mate
nice one well done loving the build.
steve

Phil Woollard · Post by **Phil Woollard** » Sat Dec 22, 2018 8:57 am

Many thanks Steve and all the followers that click the like box! Some examples of what I have planned for more detail below.

yves mouton · Post by **yves mouton** » Sat Dec 22, 2018 9:54 am

Hello Phil,

Amazing job so far on the famo Phil

Best regards Yves

Phils Famo build

Re: Phils Famo build

Re: Phils Famo build

Re: Phils Famo build

Re: Phils Famo build

Re: Phils Famo build

Re: Phils Famo build

Re: Phils Famo build

Re: Phils Famo build

Re: Phils Famo build

Re: Phils Famo build

Re: Phils Famo build

Re: Phils Famo build

Re: Phils Famo build

Re: Phils Famo build

Re: Phils Famo build