331 gets a makeover

Forum for discussion relating to Tiger 1, Mid, Early, Late Production and Sturmtiger
Post Reply
Phil Woollard
Posts: 4264
Joined: Mon Mar 01, 2010 4:48 pm
Location: Cornwall
Has liked: 2254 times
Been liked: 7137 times

331 gets a makeover

Post by Phil Woollard »

Some of you may be interested in this makeover, well I will try to make it interesting.
It will be for sale at some point.
Attachments
IMG_20240808_141300.jpg
I shall be removing the blank firing device.
I shall be removing the blank firing device.
New standard tracks
New standard tracks
A pair of Liams superb idlers, new track pin washers and split pins, not my favourite job but it has to be done.
A pair of Liams superb idlers, new track pin washers and split pins, not my favourite job but it has to be done.
The silver rim has been turned to replicate road wheel rubbing, which happened a lot .
The silver rim has been turned to replicate road wheel rubbing, which happened a lot .
Red oxide base
Red oxide base
IMG_20240808_155712.jpg
Matt black applied sparingly
Matt black applied sparingly
Note the old batteries used to block the hull, you can safely run the tank flat out if you require, you can of course use a secondary lift but I'm happy using the old batteries
Note the old batteries used to block the hull, you can safely run the tank flat out if you require, you can of course use a secondary lift but I'm happy using the old batteries
Lots of detail on this model
Lots of detail on this model
I'm using a small wire brush to remove the paint
I'm using a small wire brush to remove the paint
IMG_20240808_162656.jpg
That's enough ground contact area weathering for now
That's enough ground contact area weathering for now
IMG_20240808_163117.jpg
With just a few minutes of run time the natural weathering begins
With just a few minutes of run time the natural weathering begins
IMG_20240808_163511.jpg
Last edited by Phil Woollard on Thu Aug 08, 2024 8:39 pm, edited 1 time in total.
Mechanical engineer.
2 Youtube channels, Phil Woollard and Magpiespyro. Facebook/ Phil Woollard.
Commission builds considered. Pm for my email.
Top
User avatar
Marco Peter
Posts: 529
Joined: Mon Feb 26, 2018 12:05 pm
Has liked: 1347 times
Been liked: 773 times

Re: 331 gets a makeover

Post by Marco Peter »

Nice old-style turret bin!
'Konan', my Tiger 1 Mid
'Gunther', my Panther G
Top
Brian Leighton
Posts: 4
Joined: Fri Nov 20, 2020 9:22 am
Has liked: 1 time

Re: 331 gets a makeover

Post by Brian Leighton »

Is the blank firing device for sale?
Top
Phil Woollard
Posts: 4264
Joined: Mon Mar 01, 2010 4:48 pm
Location: Cornwall
Has liked: 2254 times
Been liked: 7137 times

Re: 331 gets a makeover

Post by Phil Woollard »

Yes Brian it is. PM me for details.
Mechanical engineer.
2 Youtube channels, Phil Woollard and Magpiespyro. Facebook/ Phil Woollard.
Commission builds considered. Pm for my email.
Top
Phil Woollard
Posts: 4264
Joined: Mon Mar 01, 2010 4:48 pm
Location: Cornwall
Has liked: 2254 times
Been liked: 7137 times

Re: 331 gets a makeover

Post by Phil Woollard »

I thought I'd have a quick look at the final drive to check the "witness marks" to make sure all is well.
Attachments
The sprockets are the one piece examples and pop off the without any drama ( I machined these to accept taper lock), she's had around 10 hrs run time with a nice amount of the environment build up, which I don't want to remove.
The sprockets are the one piece examples and pop off the without any drama ( I machined these to accept taper lock), she's had around 10 hrs run time with a nice amount of the environment build up, which I don't want to remove.
Only assembly marks on the inner sprocket cone face
Only assembly marks on the inner sprocket cone face
IMG_20240810_105130.jpg
No rubbing marks here.
No rubbing marks here.
The hull inner face that the driven gear could rub against is like new. There's no lateral wandering of the gear what so ever.
The hull inner face that the driven gear could rub against is like new. There's no lateral wandering of the gear what so ever.
There's probably 1 mm of clearance between the faces which the grease fills nicely
There's probably 1 mm of clearance between the faces which the grease fills nicely
Before reassembly I shall pack with fresh grease. No gasket is required, just a light smear of grease will suffice.
Before reassembly I shall pack with fresh grease. No gasket is required, just a light smear of grease will suffice.
Mechanical engineer.
2 Youtube channels, Phil Woollard and Magpiespyro. Facebook/ Phil Woollard.
Commission builds considered. Pm for my email.
Top
Phil Woollard
Posts: 4264
Joined: Mon Mar 01, 2010 4:48 pm
Location: Cornwall
Has liked: 2254 times
Been liked: 7137 times

Re: 331 gets a makeover

Post by Phil Woollard »

The BF.
Attachments
IMG_20240812_093848.jpg
IMG_20240812_093905.jpg
IMG_20240812_093929.jpg
IMG_20240812_094236.jpg
IMG_20240812_094255.jpg
Mechanical engineer.
2 Youtube channels, Phil Woollard and Magpiespyro. Facebook/ Phil Woollard.
Commission builds considered. Pm for my email.
Top
yves mouton
Posts: 998
Joined: Fri Nov 06, 2009 7:55 pm
Location: Belgium
Has liked: 1 time
Been liked: 563 times

Re: 331 gets a makeover

Post by yves mouton »

hello Phil,

That's for the first time i see a blank fire mounted like this.

Mine are with the blanks facing the barrel.

Best regards Yves
Top
Phil Woollard
Posts: 4264
Joined: Mon Mar 01, 2010 4:48 pm
Location: Cornwall
Has liked: 2254 times
Been liked: 7137 times

Re: 331 gets a makeover

Post by Phil Woollard »

Yes this one has more clearance below for the batteries. You also get a slightly bigger bang as the gases are more direct.
Mechanical engineer.
2 Youtube channels, Phil Woollard and Magpiespyro. Facebook/ Phil Woollard.
Commission builds considered. Pm for my email.
Top
Post Reply

Return to “Tiger 1”