Dale easy eight No 65

Dale jordan · Post by **Dale jordan** » Sun Feb 11, 2024 6:48 am

Just about ready for casting

: IMG_4880.jpg (134.72 KiB) Viewed 1677 times

Robert E Morey · Post by **Robert E Morey** » Sun Feb 11, 2024 5:18 pm

that looks excellent Dale - nicely done!
Bob

Dale jordan · Post by **Dale jordan** » Wed Feb 21, 2024 9:06 pm

Quick question are the 8mm pins for the suspension pivots stainless steel ? Dale

Robert E Morey · Post by **Robert E Morey** » Thu Feb 22, 2024 6:10 pm

Dale
I don't think so, I think they are carbon (ie non-stainless) steel. I replaced mine with 316SS to prevent rust.
Bob

jwwirds · Post by **jwwirds** » Thu Feb 22, 2024 8:06 pm

I’m not sure whether it’s stainless. I exchanged mine for a brass tube. I put a thread in the tubes so I can remove them if necessary.

Dale jordan · Post by **Dale jordan** » Thu Feb 22, 2024 10:48 pm

Really happy with the look of the casting detail on the suspension arms I filled the webbing holes from the back . Dale

: IMG_4896.jpg (94.51 KiB) Viewed 1412 times

: IMG_4897.jpg (121.91 KiB) Viewed 1412 times

Dale jordan · Post by **Dale jordan** » Fri Mar 08, 2024 3:49 am

One finished five to go . Dale

: IMG_4925.jpg (116.95 KiB) Viewed 1280 times

: IMG_4927.jpg (137.29 KiB) Viewed 1280 times

Robert E Morey · Post by **Robert E Morey** » Sat Mar 09, 2024 5:15 pm

Excellent Dale - I agree really nice addition.
Bob

Dale jordan · Post by **Dale jordan** » Fri Mar 15, 2024 3:31 am

Lower hull painted Olive Drab . Test fitting bogie number one I used loctite 480 for the first time boy its strong I had one tyre on crooked had all types of trouble getting it off . I hat to use a razor knife to get under the rubber , lucky only one to do . Dale

: IMG_4942.jpg (156.43 KiB) Viewed 1052 times

: IMG_4939.jpg (157.63 KiB) Viewed 1052 times

Dale jordan · Post by **Dale jordan** » Fri Mar 15, 2024 5:45 am

: IMG_4943.jpg (168.38 KiB) Viewed 1043 times

Dale jordan · Post by **Dale jordan** » Tue Mar 26, 2024 4:45 am

One side done . Dale

: IMG_5130.jpg (162.85 KiB) Viewed 836 times

: IMG_5123.jpg (163.71 KiB) Viewed 836 times

Dale jordan · Post by **Dale jordan** » Thu Mar 28, 2024 11:30 am

one track on . Dale

: IMG_5134.jpg (149.42 KiB) Viewed 660 times

: IMG_5137.jpg (191.49 KiB) Viewed 660 times

Dale jordan · Post by **Dale jordan** » Mon Apr 08, 2024 7:55 am

: IMG_5157.jpg (157.92 KiB) Viewed 271 times

: IMG_5158.jpg (135.03 KiB) Viewed 271 times

Following Daves lead again . I did raise the position of the MG port and over a bit as well . Dale

Dale jordan · Post by **Dale jordan** » Thu Apr 11, 2024 1:48 pm

Put a lot of work into the side hatch today plus made new lifting hooks to the correct size and repositioned them . . Dale

: IMG_5161.jpg (154.78 KiB) Viewed 195 times

: IMG_5163.jpg (130.26 KiB) Viewed 195 times

: IMG_5165.jpg (159.3 KiB) Viewed 195 times

Dale jordan · Post by **Dale jordan** » Mon Apr 15, 2024 11:11 am

A bit of work on the rear vent and gun mount Dale

: IMG_5169.jpg (139.6 KiB) Viewed 146 times

: IMG_5172.jpg (127.93 KiB) Viewed 146 times

Dale easy eight No 65

Re: Dale easy eight No 65

Re: Dale easy eight No 65

Re: Dale easy eight No 65

Re: Dale easy eight No 65

Re: Dale easy eight No 65

Re: Dale easy eight No 65

Re: Dale easy eight No 65

Re: Dale easy eight No 65

Re: Dale easy eight No 65

Re: Dale easy eight No 65

Re: Dale easy eight No 65

Re: Dale easy eight No 65

Re: Dale easy eight No 65

Re: Dale easy eight No 65

Re: Dale easy eight No 65