No. 37
-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
-
simon_manning
- Posts: 2061
- Joined: Fri Nov 02, 2007 8:51 pm
- Location: new forest,hampshire,u.k.
- Been liked: 1767 times
Re: Brian's Famo
some nice Famo building here Brian, a big project, and a big vehicle when finished, regards simon manning.
-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
-
Timo Winterlich
- Posts: 40
- Joined: Thu Nov 20, 2008 4:34 pm
- Location: Germany, Rheinland-Pfalz
- Has liked: 41 times
- Been liked: 29 times
Re: Brian's Famo
Nice Work on the wheels Brian, that had need a lot of time but looks much better than before!
Regards Timo
Manchmal muss man auch gegen den Strom schwimmen!
Manchmal muss man auch gegen den Strom schwimmen!
-
florian rudolf
- Posts: 678
- Joined: Mon Feb 29, 2016 10:53 am
- Has liked: 297 times
- Been liked: 645 times
- Contact:
Re: Brian's Famo
I would take the smaler model M3 nuts for the wheel hubs bolts Brian. It looks more realistic I think?!
-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
Re: Brian's Famo
Any one know why the fan motor is spinning at idle and not when I give it throttle?
-
Armortek
- Site Admin
- Posts: 2935
- Joined: Tue Jul 10, 2007 10:30 am
- Location: Winchester, England
- Been liked: 3699 times
Re: Brian's Famo
Few questions for you:Brian Ostlind wrote: ↑Thu Feb 04, 2021 6:16 amAny one know why the fan motor is spinning at idle and not when I give it throttle?
- Do you have the receiver connected and the radio switched on when you are experiencing this?
- Do you mean that at full throttle the fan does not spin, or does it start spinning when you switch on the power and keep spinning irrespective of the drive position ?
- Have you checked the trim settings on the drive channel ? The fan will be quite sensitive to this.
Maybe drop us an email - might be easier.
Armortek
-
Brian Ostlind
- Posts: 1466
- Joined: Sat Oct 28, 2017 6:56 am
- Location: Oregon, USA
- Has liked: 975 times
- Been liked: 2068 times
