The Official Armortek Forum - World leader in one sixth scale metal kits

Hello,

Working on some details today.



Working on the leather seats.






Also after weathering the wheels i put them on the famo and also instal the tracks.





Best regards Yves

Hello,

A small update,

Have to take off the tracks to fix the back of the famo.
it was a hell of a job to fix the bolts. I used M3 hex bolts on the outside and for the inside i used M3 button heads because you
can almoast not see them.



And did some extra details on the cabin.



Best regards Yves

Hello,
A little update,

Instal the front lights with 12v leds.



Also stared working on the dashboard, drill out the places where the decals come.
I'am gonna use acryl glass for the lights in the board.



Also working on the steering wheel with a servo that works together with the steering actuator.
Pictures comes later.

Best regards Yves

Hi Yves,
Like your FAMO building progress.

Found your FAMO front compartment had been on and off the chassis more than once. Have you met any difficulty of screwing-on the eight positions ( four on each side. See red circles on your photo.)?

I have tried doing so , yet could only screwed on two back holes. The from two holes were in a few mm offset.

Is there any procedure I have done incorrectly , or any trick I have missed ?

Regards,
Lerh Chang

Updated : Now I have sorted out the "a few mm offset" issue. But still a lot of other issues to go ...

Hi Chang,

I Did take off the front more than one time that's because i wanne fix the nose front of the famo first.
The loading area is al ready fixt. To screw in all the bolts it's a bit of hell. The holes line up correctly but no easy acces.
I use on the outside the M3 hex bolts and on the inside i use M3 button heads ( more easy to screw them in) and these ones you donth
see from the outside.

Now i'am working on the dashboard ( with lights ) and the front window ( can open and close ) that's also a lot of work.
If that is fixt i put the front of the famo back on.

Best regards Yves

Hello,

A little update,
Working on the licenceplates, front plate install.



Working on the windowscreen almoast finish.






next work to do is working on the dashboardlights.

Best regards Yves

Hello,

A small update on the famo.





Best regards Yves

Nice job on the Famo yves, coming on nicely, regards simon.

Thanks Simon,

Almoast done, just a few little things and details.
Just waiting for a new module A.
Already buy 5 crew members for the famo and 2 for the sdkfz 251.
These dolls are very expensive these days.


Best regards Yves

Hello,

New toy for the famo,
a towing set



Best regards Yves

Verry nice build Yves,
like to see it real at Overloon maybe?!

Cheers
Florian

Hello florian,

The famo fit not in my Defender
I will bring something else.

Best regards Yves

Hello,

Work on the famo starts again.

Working on some details, winch works fine.
Test drive into my car, car is just big enough.







Also working on the famo lights and the canvas for the famo.

Best regards Yves

Perfect Yves,

so we see your Famo in Overloon?

Cheers
Florian

Hello Florian,

Dont know if i take the famo, still some problems with drive and steering.
In reverse turn i donth have engough power, have to look in my transmitter setup. forward is ok.
About the steering on the wheels they turn left and right if they are of the ground, but if i put the famo on the ground they donth turn
not so good. Maybe need some change in my transmitter or else is the steering actuator not strong enough.

I think if the famo is not ready till than, i bring my stug and 251 or my kt

Best regards Yves