Page 4 of 5

Re: Steves Elefant build

Posted: Fri Feb 02, 2018 10:10 pm
by simon_manning
looks superb steve, they are a very impressive vehicle when complete, a nice job, regards simon.

Re: Steves Elefant build

Posted: Thu Feb 08, 2018 4:35 pm
by Steve Norris
Basic camofauge has now been added to the fist Elefant
Little brother acting as a pattern above
Little brother acting as a pattern above
Regards
Steve

Re: Steves Elefant build

Posted: Thu Feb 08, 2018 11:43 pm
by Ray Brown
looking good steve.

Re: Steves Elefant build

Posted: Sat Feb 10, 2018 5:56 am
by vincent hung shu yue
Hi Steve
Really good looking!
Vincent

Re: Steves Elefant build

Posted: Sat Feb 10, 2018 6:44 pm
by Chang
Hi Steve,

Two filler caps on the engine deck looks as the genuine parts. :shock:
Elefant-24c.jpg

Re: Steves Elefant build

Posted: Sat Feb 10, 2018 9:43 pm
by Steve Norris
Hi Chang
These are modified Armorpax items, they do not come with the kit.
Regards
Steve

Re: Steves Elefant build

Posted: Thu Feb 15, 2018 8:33 pm
by Steve Norris
Almost there.
The first of 2 Elefant builds is now nearing the end, electrics all sorted and just the final bits and pieces to complete.
Must say I do like the twin engine start sound supplied with the sound module.
Almost ready for its new owner
Almost ready for its new owner
Regards

Steve

Re: Steves Elefant build

Posted: Fri Feb 16, 2018 2:30 pm
by nikolas george
Mate, that looks sooo good. You can also have a father and son picture like the one Armortek took at the tank museum recently :D :D .
Or maybe take yours to the tank museum and you can have grandfather, father and son !!
Have you got it running yet ?
Nik

Re: Steves Elefant build

Posted: Fri Feb 16, 2018 2:48 pm
by Steve Norris
Hi Nik
The Elefant is a big impressive kit and will look great when running. I have tested the electrics in this one and everything works fine including the drive motors I just have not run it on the ground yet.
Regards
Steve

Re: Steves Elefant build

Posted: Fri Apr 13, 2018 8:13 pm
by Robert E Morey
Steve
Any finished pictures of the Elephants? Perhaps outside? I always enjoy your finished outside images.
Bob

Re: Steves Elefant build

Posted: Fri Apr 13, 2018 9:12 pm
by Steve Norris
Hi Robert
Unfortunately I did not get chance to get any shots outside as the weather was very bad and I needed to get both tanks to the packers.
This is about the best shot of one of the almost complete Elefants
This is about the best shot of one of the almost complete Elefants
And packed in a custom made case for shipping
And packed in a custom made case for shipping
Regards
Steve

Re: Steves Elefant build

Posted: Sat Apr 14, 2018 5:52 pm
by Robert E Morey
Lucky customers to have your beautiful work! They look great!
B

Re: Steves Elefant build

Posted: Wed Jun 27, 2018 10:30 am
by Dave Jones
Steve, hope you don't mind but I'm looking for a bit of advice.

I have just finished building the lower hull, all looks good except I have a gap between CR102 Upper Front plate and CR104 Hull Plate (see photo). Did you encounter this or have I simply run out of talent and got something upside down or back to front?

Appreciate your thoughts.

Thanks.

Dave
Lower Hull.jpg
Lower Hull.jpg (81.88 KiB) Viewed 6113 times

Re: Steves Elefant build

Posted: Wed Jun 27, 2018 12:21 pm
by Chang
Hi Dave,
I think this gap is there for every builder. Mine has got it. I simply fill it with car filler. Photos will be shown later.

Regards,
Lerh Chang

Re: Steves Elefant build

Posted: Wed Jun 27, 2018 1:53 pm
by Dave Jones
Hi Chang

Thanks for the feedback. Out with the Milliput it is then. I'll fill the gap when I do the weld detail. I just wanted to make sure I hadn't done anything daft before I moved on too far.

Cheers!

Dave.