Re: Sd.Kfz.7/1 and 20mm Flakvierling 38
Posted: Fri Jun 20, 2014 8:05 pm
Striped it down a bit and started on my electrics,motors first and a few other bits
Page 8 of 16
Re: Sd.Kfz.7/1 and 20mm Flakvierling 38
Posted: Sat Jun 21, 2014 10:24 pm
Winch motor fitted
Re: Sd.Kfz.7/1 and 20mm Flakvierling 38
Posted: Sun Jun 22, 2014 12:10 am
Hi Phil
Coming along really well.
Will the drive motors go in with out seperating the chasis ?
It looks a bit of a tight fit.
Derek
Coming along really well.
Will the drive motors go in with out seperating the chasis ?
It looks a bit of a tight fit.
Derek
Re: Sd.Kfz.7/1 and 20mm Flakvierling 38
Posted: Sun Jun 22, 2014 6:16 am
Thanks Derek,
Yes the motors went in easily,Ive got some more photo's on my camera
that I haven't got round to getting on the computer.
If you have your motion pack aswell before you start,it is a good idea
to fit the little bush that supports the end of the motor shaft,into
the gear box recess at the early chassis stage.
Otherwise you end up balancing it on the end of your finger and poking it through the
hole in the chassis.
mine needed a bit of emery paper for a better fit.
Also the stearing servo might be easier fitting at the chassis stage.
Cheers
Phil
Yes the motors went in easily,Ive got some more photo's on my camera
that I haven't got round to getting on the computer.
If you have your motion pack aswell before you start,it is a good idea
to fit the little bush that supports the end of the motor shaft,into
the gear box recess at the early chassis stage.
Otherwise you end up balancing it on the end of your finger and poking it through the
hole in the chassis.
mine needed a bit of emery paper for a better fit.
Also the stearing servo might be easier fitting at the chassis stage.
Cheers
Phil
Re: Sd.Kfz.7/1 and 20mm Flakvierling 38
Posted: Mon Jun 23, 2014 4:55 pm
Drive Motors fitted
Re: Sd.Kfz.7/1 and 20mm Flakvierling 38
Posted: Mon Jun 23, 2014 9:01 pm
Used part of the battery tray for my speaker
Re: Sd.Kfz.7/1 and 20mm Flakvierling 38
Posted: Tue Jun 24, 2014 7:14 pm
Stearing servo and linkage
Re: Sd.Kfz.7/1 and 20mm Flakvierling 38
Posted: Wed Jun 25, 2014 8:18 pm
Made my own battery tray to sink as low as possible.
Re: Sd.Kfz.7/1 and 20mm Flakvierling 38
Posted: Wed Jun 25, 2014 10:53 pm
Made some Sub Decks for my electronics,just enough clearance.
Re: Sd.Kfz.7/1 and 20mm Flakvierling 38
Posted: Thu Jun 26, 2014 8:02 pm
My battery set now sits nice and low and room for my power supply.
Re: Sd.Kfz.7/1 and 20mm Flakvierling 38
Posted: Fri Jun 27, 2014 7:36 pm
Power supply fitted on top of battery set,access to power button through
engine grill.
engine grill.
Re: Sd.Kfz.7/1 and 20mm Flakvierling 38
Posted: Sat Jun 28, 2014 7:41 am
The rest of the electrics sitting on the sub decks,the exhaust system
still to go in,just had to take the screws out of the module covers,
clearance is nill between deck.
The clearance between middle sub deck and winch top bolts is a piece of 180
wet and dry
The black cable protector disguises all the bright colours.
still to go in,just had to take the screws out of the module covers,
clearance is nill between deck.
The clearance between middle sub deck and winch top bolts is a piece of 180
wet and dry
The black cable protector disguises all the bright colours.
Re: Sd.Kfz.7/1 and 20mm Flakvierling 38
Posted: Sat Jun 28, 2014 8:22 am
Nice neat layout. Great to see this part.
John
John
Re: Sd.Kfz.7/1 and 20mm Flakvierling 38
Posted: Sat Jun 28, 2014 1:24 pm
Thanks John 
I might spray just the one edge of the speed controller and amplifier module,with
the dark yellow,so that it doesn't stand out so much.
Cheers
Phil
I might spray just the one edge of the speed controller and amplifier module,with
the dark yellow,so that it doesn't stand out so much.
Cheers
Phil
Re: Sd.Kfz.7/1 and 20mm Flakvierling 38
Posted: Sat Jun 28, 2014 8:13 pm
Phil,
Your SDKFZ 7 is looking great. Very nice install with the electronics. Are you planning on the Armored cab? Beautiful job on the rear deck. I'd love to build one of these someday. Fantastic work as always.
Best regards,
Bob
Your SDKFZ 7 is looking great. Very nice install with the electronics. Are you planning on the Armored cab? Beautiful job on the rear deck. I'd love to build one of these someday. Fantastic work as always.
Best regards,
Bob