A basic question regarding the wiring up of the motors.
A red marker on the 'positive' terminal?
I'm assuming that these are straight forward DC motors with nothing fancy inside of them to damage and it doesn't matter which way around the wiring is connected.
I'm asking because I need to change the rotation direction of one of the motors to get the same forward gear direction when the motors are side by side - gears pointing outwards.
Drive Motor Wiring
-
- Posts: 232
- Joined: Mon Oct 31, 2022 1:37 am
- Location: Evesham, Worcestershire
- Has liked: 374 times
- Been liked: 875 times
- Contact:
- Gerhard Michel
- Posts: 619
- Joined: Tue Oct 04, 2016 12:27 pm
- Location: near Nuremberg, Germany
- Has liked: 3 times
- Been liked: 617 times
Re: Drive Motor Wiring
Hi Malcolm,
motors in tank models have to run in both directions; otherwise the model could not move backwards. Therefore they need changing polarity.
motors in tank models have to run in both directions; otherwise the model could not move backwards. Therefore they need changing polarity.
kind regards
Gerhard
____________________________________________________________________
1/6 Scale models: Jagdpanther (AT), Jagdtiger (BT), Königstiger (Porsche turret, NH), Königstiger (Production turret, BT), Pz. IV (SH)
Gerhard
____________________________________________________________________
1/6 Scale models: Jagdpanther (AT), Jagdtiger (BT), Königstiger (Porsche turret, NH), Königstiger (Production turret, BT), Pz. IV (SH)
-
- Posts: 232
- Joined: Mon Oct 31, 2022 1:37 am
- Location: Evesham, Worcestershire
- Has liked: 374 times
- Been liked: 875 times
- Contact:
Re: Drive Motor Wiring
Hi Gerhard
Thought so and have now swapped it over.
Best to be 100% certain I think.
Thought so and have now swapped it over.
Best to be 100% certain I think.
2022 Panther G #15
-
- Posts: 72
- Joined: Fri May 13, 2022 8:38 pm
- Has liked: 28 times
- Been liked: 29 times
Re: Drive Motor Wiring
Hello can you elaborate how you swapped them changing the yellow and blue around or moving one wire to the other motor I'm learning about polarity any help is appreciated
- Adrian Harris
- Posts: 5043
- Joined: Thu Jul 12, 2007 10:46 pm
- Location: Berkshire (UK)
- Has liked: 1355 times
- Been liked: 1550 times
Re: Drive Motor Wiring
Just swapping the blue and yellow over on one motor.
Adrian.
Adrian.
Contact me at sales@armortekaddict.uk for details of my smoker fan control module
-
- Posts: 72
- Joined: Fri May 13, 2022 8:38 pm
- Has liked: 28 times
- Been liked: 29 times
Re: Drive Motor Wiring
Ok thank you do you speed one track up and slow the other to steer or reverse one track the opposite direction cause I can't get mine to reverse direction on a one stick set up without all stick inputs reversing the motors opposite each other. I'm using a DXS8 but also have the frsky I can use.....the spectrum is easier for me though. I'm going to try dual Ail rudder and elevator today but not sure if it will work. I'm pondering a flysky p18 radio next but would like to avoid it
- Adrian Harris
- Posts: 5043
- Joined: Thu Jul 12, 2007 10:46 pm
- Location: Berkshire (UK)
- Has liked: 1355 times
- Been liked: 1550 times
Re: Drive Motor Wiring
Any time one track is running faster than the other, the tank will turn towards the slower track.
You can change the relative speeds, stop one track or have them going in opposite directions (neutral turn).
When I was using Spektrum, I used Elevon-B I think. I would adjust the transmitter, so that forward on the stick made both channels go positive on the channel monitor, then change the motor wiring so that the motors drove the sprockets forward. Then if it turned left instead of right, I would swap the leads for the tracks over in the receiver.
You also need to increase the end points on the channels used on the single stick to 150%, otherwise you won't get full speed out of the tank.
Adrian.
You can change the relative speeds, stop one track or have them going in opposite directions (neutral turn).
When I was using Spektrum, I used Elevon-B I think. I would adjust the transmitter, so that forward on the stick made both channels go positive on the channel monitor, then change the motor wiring so that the motors drove the sprockets forward. Then if it turned left instead of right, I would swap the leads for the tracks over in the receiver.
You also need to increase the end points on the channels used on the single stick to 150%, otherwise you won't get full speed out of the tank.
Adrian.
Contact me at sales@armortekaddict.uk for details of my smoker fan control module
-
- Posts: 72
- Joined: Fri May 13, 2022 8:38 pm
- Has liked: 28 times
- Been liked: 29 times
Re: Drive Motor Wiring
Thank you I appreciate your input....no pun....but I will try that for certain