Chieftain build by Phil Woollard.

Phil Woollard · Post by **Phil Woollard** » Sat May 09, 2020 8:19 pm

Printing underway!

Vince Cutajar · Post by **Vince Cutajar** » Sat May 09, 2020 8:43 pm

Found a photo of the exhaust expansion box you mentioned a couple of days ago and made a quick draft of it. Obviously all dimensions are not correct.

Vince

Stephen White · Post by **Stephen White** » Sat May 09, 2020 9:16 pm

Vince

You asked and I've found this in my files:

Trust it will help you. Stephen

Phil Woollard · Post by **Phil Woollard** » Sat May 09, 2020 9:22 pm

You have been busy vince! We could do with ivano's dimension of the main engine exhausts centres , I will take some measurements and we could do draft to see if it will work?

Just seen your post Stephen and thank you once again, I will have a look tomorrow and digest the figures.

Vince Cutajar · Post by **Vince Cutajar** » Sat May 09, 2020 9:52 pm

Trust it will help you. Stephen

Thanks for that Stephen. Having a top view and side view really helps.

Phil that silencer looks good.

Vince

Phil Woollard · Post by **Phil Woollard** » Sun May 10, 2020 7:56 am

There's lots of interesting angles going on with both the exhaust systems, the auxiliary engine has a very long run, I shall enjoy replicating that lot very much!

Ivano we need to know the centres of these pipes taken from the L60 engine you are making for us?

Phil Woollard · Post by **Phil Woollard** » Sun May 10, 2020 1:21 pm

Engine/gearbox bay geu exhaust work. I do enjoy fabricating these.

Vince Cutajar · Post by **Vince Cutajar** » Sun May 10, 2020 1:43 pm

What's the diameter of those two copper pipes? 1/2" or 3/4"?
Vince

Phil Woollard · Post by **Phil Woollard** » Sun May 10, 2020 1:52 pm

15 mm vince.

Vince Cutajar · Post by **Vince Cutajar** » Sun May 10, 2020 2:18 pm

I wasn't too far off. I modelled mine as 16mm.
Also be advised that although my drawing shows pipes with bellows, they are not functional. They are not flexible. Also I can't draw bends in bellows.
Vince

Phil Woollard · Post by **Phil Woollard** » Sun May 10, 2020 2:56 pm

That's fine Vince I can sort the bends out.

Ivano Costantini · Post by **Ivano Costantini** » Mon May 11, 2020 9:03 am

Hi Phil,
i have not reproduced the exhausts,
there was no space. I can give you this size, the tubes are on the sides of the head. The brackets measure 14.5 mm. they are not sure they are correct, maybe you will have to do it again. Without the tank it is difficult to guess. Tell me if the information is useful.
Thanks!

Ivano Costantini · Post by **Ivano Costantini** » Mon May 11, 2020 9:07 am

Sorry, here are the photos

Phil Woollard · Post by **Phil Woollard** » Mon May 11, 2020 9:14 am

Thanks Ivano that's great.
Now I have the false floor over the electric motors I can give you the exact distance between the "T piece" and the floor if you like?

Ivano Costantini · Post by **Ivano Costantini** » Mon May 11, 2020 9:49 am

Thanks but I don't think I need it, the boxes of the sefrigerante are already in print. Also for the other pieces the OK was given for the realization. We cross our fingers and hope well!

Chieftain build by Phil Woollard.

Re: Chieftain build by Phil Woollard.

Re: Chieftain build by Phil Woollard.

Re: Chieftain build by Phil Woollard.

Re: Chieftain build by Phil Woollard.

Re: Chieftain build by Phil Woollard.

Re: Chieftain build by Phil Woollard.

Re: Chieftain build by Phil Woollard.

Re: Chieftain build by Phil Woollard.

Re: Chieftain build by Phil Woollard.

Re: Chieftain build by Phil Woollard.

Re: Chieftain build by Phil Woollard.

Re: Chieftain build by Phil Woollard.

Re: Chieftain build by Phil Woollard.

Re: Chieftain build by Phil Woollard.

Re: Chieftain build by Phil Woollard.