Florians FAMO build

florian rudolf · Post by **florian rudolf** » Tue Dec 18, 2018 1:42 pm

Phil is right.
a) The secound position I did
b) don't cut the shaft nut.
You will see the hole on the top of the case over the shaft nut. I set the shaft nut in the rigt way (like I wrote it allready). Than make the hole about 3mm deeper in the brass, fixing the shaft nut with loctite, and install the pin as in the manual, also with loctite. so you have the right position for the shaft nut fixed.

Phil Woollard · Post by **Phil Woollard** » Sun Dec 30, 2018 9:15 am

Hi Florian, looking back through your thread and looking at your drive sprockets, have you bonded the rubber to the sprockets in that position ?

florian rudolf · Post by **florian rudolf** » Thu Jan 10, 2019 10:18 am

Hello @ all,
after the x-Mass break, I'll continue my report. Made some details finish for the fame

florian rudolf · Post by **florian rudolf** » Thu Jan 10, 2019 10:25 am

The special fasteners for the track chain, coming soon in end of March. so this one who want a set, and did'nt order it. Please PM.
I have a previos set...

David Brady · Post by **David Brady** » Thu Jan 10, 2019 10:29 am

Nice details added florian

Phil Woollard · Post by **Phil Woollard** » Fri Jan 11, 2019 8:29 am

Very nice bonnet vents Florian.

florian rudolf · Post by **florian rudolf** » Fri Jan 11, 2019 10:16 am

Thanks for the feedback. Its easyer to work on it, if you know that somebody appreciates it.

florian rudolf · Post by **florian rudolf** » Mon Jan 14, 2019 8:27 am

Some more details. Now Iam on the window frame and the exhaust pipes.
Sorry for the bad photo quality, but you can see the rivets I have set and the new position for the handrail.

florian rudolf · Post by **florian rudolf** » Thu Jan 17, 2019 11:17 am

I'm back, making some more details on may wind sheeld. Unfortunatly my window is broken while I install it in the frame. So I must built an new one in time...
I installed it provisionally, so not all fasteners are fixed, and I ahve'nt the wing-nut yet.

florian rudolf · Post by **florian rudolf** » Mon Jan 21, 2019 9:24 am

Its could outside, so I worked a bit on more function details. Making the winkers.

Phil Woollard · Post by **Phil Woollard** » Mon Jan 21, 2019 11:41 am

Very nice detail piece Florian

florian rudolf · Post by **florian rudolf** » Mon Jan 21, 2019 4:43 pm

Thanks Phil. I Hope its a good effect in the end.

florian rudolf · Post by **florian rudolf** » Tue Jan 22, 2019 10:36 am

Yesterday I installed the mechanik for the winker and connect it with the winkers. So this work is completly done.

Phil Woollard · Post by **Phil Woollard** » Tue Jan 22, 2019 1:09 pm

Looking good. Have you bonded the sprocket rubbers in that position Florian or are they loose?

florian rudolf · Post by **florian rudolf** » Tue Jan 22, 2019 3:17 pm

Hi Phil,
they are loose in time. Why do you ask?
I made the rubber with dubble tape, because I don't know the realy right position now.

Florians FAMO build

Re: Florians FAMO build

Re: Florians FAMO build

Re: Florians FAMO build

Re: Florians FAMO build

Re: Florians FAMO build

Re: Florians FAMO build

Re: Florians FAMO build

Re: Florians FAMO build

Re: Florians FAMO build

Re: Florians FAMO build

Re: Florians FAMO build

Re: Florians FAMO build

Re: Florians FAMO build

Re: Florians FAMO build

Re: Florians FAMO build